English- Français (French)
S Trap with Solvent Weld Joint & Cleanout HxH
Installed in an ABS DWV pipe system beneath a sink or drain to prevent sewer gas from entering the building. The U-Bend is attached to the drain tail piece using an adapter sized to match the tail pipe.Features
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten plus a half turn provides a complete seal
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
ABS DWV 1 1/2” S TRAP WITH CLEAN OUT
Resources
OTHER TOOLS
Threaded Plug for 1 1/2" S Trap
Used for Canplas Industries Ltd ABS DWV S-Trap model number 103251A as a replacement part if damaged during maintenance.Features
• Self sealing plug , no gasket required
• Cap body Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Cap body Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
ABS DWV Threaded Plug for 1-1/2" S Trap
Resources
OTHER TOOLS
P Trap with Solvent Weld Joint HxH
Installed in a ABS DWV pipe system beneath a bathroom sink tail piece. The U-Bend is connected to the Sink Tail Piece using a Trap Adapter sized to match the Tail pipe. The 90 Degree part of the assembly is then cemented to the U-Bend and directed toward the rest of the ABS DWV drainage line.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Warning: Canplas Recommends Sponge Rubber and Wax Gaskets Only for use with all Plastic Closet Flanges
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Warning: Canplas Recommends Sponge Rubber and Wax Gaskets Only for use with all Plastic Closet Flanges
• Warning: Canplas Recommends Sponge Rubber and Wax Gaskets Only for use with all Plastic Closet Flanges
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/4" ABS DWV P-Trap H X H
1-1/2" ABS DWV P-Trap Solvent Weld Joint H X H
1-1/2" ABS DWV P-Trap Solvent Weld Joint H X H
2" ABS DWV P-Trap Solvent Weld Joint H X H
3" ABS DWV P-Trap Solvent Weld Joint H X H
4" ABS DWV P-Trap Solvent Weld Joint H X H
4" X 3" ABS DWV-Trap Solvent Weld Joint H X H
Resources
OTHER TOOLS
P Trap with Cleanout & Union Connection HxH
Installed in a ABS DWV pipe system beneath a bathroom or kitchen sink to prevent sewer gas from entering a building. The U-Bend is connected to the Sink Tail Piece using an Adapter sized to match the Tail pipe. The 90 Degree part of the assembly is then screwed to the U-Bend and directed toward the rest of the ABS DWV drainage line.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic and provided with a reusable watertight gasket and Plug
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Injection molded in durable ABS plastic and provided with a reusable watertight gasket and Plug
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/4" ABS DWV P-Trap with Threaded Cleanout Plug and Gasket, Union Connection H X H
1-1/2" ABS DWV P-Trap with Threaded Cleanout Plug and Gasket, Union Connection H X H
2" ABS DWV P-Trap with Threaded Cleanout Plug and Gasket, Union Connection H X H
Resources
OTHER TOOLS
P Trap with Cleanout & Solvent Weld Joint HxH
Installed in a ABS DWV pipe system beneath a bathroom sink tail piece. The U-Bend is connected to the Sink Tail Piece using a Trap Adapter sized to match the Tail pipe. The 90 Degree part of the assembly is then cemented to the U-Bend and directed toward the rest of the ABS DWV drainage line.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic and provided with a plug and reusable watertight gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Injection molded in durable ABS plastic and provided with a plug and reusable watertight gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/4" ABS DWV P-Trap with Cleanout and Solvent Weld Joint, Cleanout Washer and Plug H X H
1-1/2" ABS DWV P-Trap, Cleanout, Solvent Weld Joint, C/O Washer and Plug H X H.
1-1/2" ABS DWV P-Trap with a Threaded Cleanout Plug and Gasket, Weld Joint H X H
2" ABS DWV P-Trap with a Threaded Cleanout Plug and Gasket, Weld Joint H X H
Resources
OTHER TOOLS
P Trap with Union HxH
Installed in a ABS DWV pipe system beneath a bathroom or kitchen sink to prevent sewer gas from entering a building. The U-Bend is connected to the Sink Tail Piece using an Adapter sized to match the Tail pipe. The 90 Degree part of the assembly is then screwed to the U-Bend and directed toward the rest of the ABS DWV drainage line.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/4" ABS DWV P-Trap, Union Connection H X H
1-1/2" ABS DWV P-Trap, Union Connection H X H
1-1/2" ABS DWV P-Trap, Union Connection H X H
2" ABS DWV P-Trap, Union Connection H X H
Resources
OTHER TOOLS
P Trap LA Pattern with Union SlipxH
Installed in a ABS DWV pipe system beneath a bathroom or kitchen sink to prevent sewer gas from entering a building. The U-Bend is connected to the Sink Tail Piece using an Adapter sized to match the Tail pipe. The 90 Degree part of the assembly is then screwed to the U-Bend and directed toward the rest of the 1-1/2" ABS DWV drainage line.Features
• Hub connection can be single step ABS solvent cemented
• Injection molded body in durable ABS plastic and using a reliable slip nut and watertight washer
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Injection molded body in durable ABS plastic and using a reliable slip nut and watertight washer
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Normally used in the drainage portion of the DWV system only
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" ABS DWV P-Trap (LA Pattern) Union Connection Poly Washer and Nut, H X Slip Connection
Resources
OTHER TOOLS
P Trap Cleanout Cap Self Sealing (no gasket)
Used for Canplas Industries Ltd ABS DWV P-Traps model numbers 103201A & 103211A, year 2009 and newer.Features
• Self sealing plug , no gasket required
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Can be hand tightened for a complete seal
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Can be hand tightened for a complete seal
• Teflon tape is recommended for threaded joints
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" - 2" ABS DWV P-Trap Cleanout Cap Self Sealing Plug with No Gasket
Resources
OTHER TOOLS
P Trap U Bend HxH
Installed in an ABS DWV pipe system beneath a shower tub, floor drain or roof drain. The U-Bend is connected to the fixture Tail Piece using pipe and adapters. It can also be used on a vertical outside pipe vent to prevent debris from entering the venting system.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Warning: Canplas Recommends Sponge Rubber and Wax Gaskets Only for use with all Plastic Closet Flanges
• Injection molded in durable ABS plastic
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Warning: Canplas Recommends Sponge Rubber and Wax Gaskets Only for use with all Plastic Closet Flanges
• Friction fitted to DWV Pipe sizes
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
2" ABS DWV U Bend H X H
3" ABS DWV U Bend H X H
4" ABS DWV U Bend H X H
6" ABS DWV U Bend H X H
Resources
OTHER TOOLS
P Trap Cleanout Cap with Gasket
Used for Canplas Industries Ltd ABS DWV P-Traps model numbers 103201A & 103211A, year 2008 and earlier and 103201S, 103202A & 103231 all years.Features
• Threaded cap provided with a reuseable watertight gasket
• Cap body Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Can be hand tightened for a complete seal
• Cap body Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Can be hand tightened for a complete seal
• Teflon tape is recommended for threaded joints
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" - 2" ABS DWV P-Trap Cleanout Cap with Gasket
Resources
OTHER TOOLS
We are always here to help.
Do not hesitate to get in touch for any reason.
