Fitting Trap Adapter less Washer & Nut SpgxMPT

Installed in an ABS DWV piping system to provide a smooth transition from a Hub to a Male National Pipe Thread (MPT).

Features
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102801
1-1/2" ABS DWV Trap Adapter (Fitting Male Adapter) Spigot X Male National Pipe Thread (MPT)
102802
2" ABS DWV Trap Adapter (Fitting Male Adapter) Spigot X Male National Pipe Thread (MPT)
103211-11BC
1 1/2" X 1 1/4" ABS DWV Trap Adapter Spigot X MPT
Resources

OTHER TOOLS

Male Adapter MPTxH

Installed in an ABS DWV piping system to transition from a standard female threaded fitting to a ABS DWV Pipe.

Features
• Hub connection can be single step ABS solvent cemented to a Pipe or Spigot connection. Teflon tape is recommended for threaded joints
• Injection molded in durable ABS plastic
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102860
1-1/2" X 1-1/4" ABS DWV Male Adapter Male National Pipe Thread (MPT) X H
Resources

OTHER TOOLS

Fitting Trap Adapter with One Piece Poly Nut

Installed under a sink to transition from the sink drain tale piece to the ABS DWV P-Trap assembly.

Features
• Spigot connection can be single step ABS solvent cemented to an ABS DWV Hub
• Injection molded body in durable ABS plastic and using a reliable one-piece Polyethylene nut and gasket assembly
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Used to protect piping from dust and moisture during shipment
• Friction fitted to DWV Pipe sizes
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102804A
1-1/2" ABS DWV Fitting Trap Adapter, with One - Piece Polyethylene Nut Spigot X Slip
102806A
1-1/4" X 1-1/2" ABS DWV Fitting Trap Adapter, with One - Piece Polyethylene Nut Spigot X Slip
Resources

OTHER TOOLS

2 in 1 Combination Trap Adapter HxSlip

Installed under a bathroom or kitchen sink to transition from a tubular 1-1/4 or 1-1/2" sink drain tale piece to the 1-1/2" ABS DWV P-Trap assembly.

Features
• Hub connection can be single step ABS solvent cemented to a Pipe or Spigot connection
• Injection molded body in durable ABS plastic and using reliable Polyethylene gaskets
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Used to protect piping from dust and moisture during shipment
• Friction fitted to DWV Pipe sizes
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102859A
1-1/2" X 1-1/2" X 1-1/4" ABS DWV Combo Trap Adapter Poly Washers and Nut Spigot X Slip Connection
Resources

OTHER TOOLS

Tray Plug Adapter

Installed in a 1-1/2" ABS DWV pipe system beneath a Laundry Tray to connect the Tray to the Drainage system. A Tray Strainer with a gasket, screws thru the Laundry Tray into the adapter. The adapter is then connected to a 1-1/2" P-Trap assembly.

Features
• Hub connection can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten plus a half turn provides a complete seal
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
103211-7
1-1/2" ABS DWV Tray Plug Adapter Spigot X Female National Pipe Thread (FPT)
103211-9
1-1/2" ABS DWV Tray Plug Adapter H X Female National Pipe Thread (FPT)
Resources

OTHER TOOLS

Copper to DWV Pipe Adapter HxSlip

Installed in an ABS DWV piping system to transition from a Copper Pipe to an ABS DWV Pipe.

Features
• Hub connection can be single step ABS solvent cemented to a 2" Pipe or Spigot connection
• Injection molded body in durable ABS plastic and using a reliable Polyethylene gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Friction fitted to DWV Pipe sizes
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102861A
1-1/2" ABS DWV Copper to ABS DWV Pipe Adapter with Washer and Nut H X Slip
102862A
1-1/4" ABS DWV Copper to ABS DWV Pipe Adapter with Washer and Nut H X Slip
102864A
1-1/2" X 1-1/4" ABS DWV Copper to ABS DWV Pipe Adapter with Gasket and Nut H X Slip
102865A
2" ABS DWV Copper to ABS DWV Pipe Adapter with gasket and Nut H X Slip
Resources

OTHER TOOLS

Union

Installed in an ABS DWV piping system to allow for a mechanical threaded connection between two solvent cemented ABS Pipes.

Features
• Hub connections can be single step ABS solvent cemented to Pipe or Spigot connections
• Injection molded body in durable ABS plastic and using a reliable Polyethylene gasket
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102863A
1-1/2" X 1-1/2" ABS DWV Threaded Union with Gasket H X H
Resources

OTHER TOOLS

Swivel Tray Plug Strainer Adapter with Washer

Installed in an ABS DWV pipe system beneath a Laundry Tray to connect and transition the threaded tray strainer basket to the drainage system.

Features
• Spigot connection can be single step ABS solvent cemented
• Injection molded body in durable ABS plastic and using a reliable reusable watertight gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Union joint is self sealing, no teflon tape required
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
103215
1-1/2" ABS DWV Swivel Tray (Strainer) Adapter with Gasket, Spigot X Female Pipe Thread
103216
1-1/2" X 1-1/2" ABS DWV Swivel Tray (Strainer) Adapter with Gasket, Long Spigot X Female Pipe Thread
103217
1-1/2" X 1-1/2" ABS DWV Swivel Tray (Strainer) Adapter with Gasket, H X Female Pipe Thread
Resources

OTHER TOOLS

Slip Joint Washer

Washer is used as a replacement part for slip joint trap adapters and together with a correctly sized nut, provide a watertight seal around sink tail pipes.

Features
• Old seals can be disposed of in a municipal recycling program
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Can be used as end caps for pipe used to transport smaller sized pipe
• Used to protect piping from dust and moisture during shipment
• Friction fitted to DWV pipe sizes
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
109210-003
1-1/4" Slip Joint Polyethylene Washer
109210-004
1-1/2" Slip Joint Polyethylene Washer
109210-005
2" Slip Joint Polyethylene Washer
Resources

OTHER TOOLS

90° Trap Adapter

Installed in an ABS DWV piping system from a sink drain tail pipe using a 90 Degree Trap Adapter, into an ABS DWV Pipe. Often used in a Pedestal Sink installation.

Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Snap in plug is molded on fitting for use during rough in
• Teflon tape is recommended for threaded joints
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
112281A
1-1/2" X 1-1/2" PVC DWV 90 Degree Trap Adapter H X Slip Joint Polyethylene Gasket and Nut
112286A
1-1/2" X 1-1/4" PVC DWV 90 Degree Trap Adapter H X Slip Joint Polyethylene Gasket and Nut
Resources

OTHER TOOLS

Trap Adapter with Washer & Nut HxSlip Joint

Installed under a bathroom sink to transition from the tubular sink drain tale piece to the ABS DWV P-Trap assembly.

Features
• Hub connection can be single step ABS solvent cemented to a Pipe or Spigot connection
• Injection molded body in durable ABS plastic and using a reliable Polyethylene gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102850A
1-1/4" ABS DWV Trap Adapter with Washer and Nut H X Slip Connection
102851A
1-1/2" ABS DWV Trap Adapter with Washer and Nut H X Slip Connection
102852A
2" ABS DWV Trap Adapter with Washer and Nut H X Slip Connection
102860A
1-1/2" X 1-1/4"ABS DWV Trap Adapter with Washer and Nut H X Slip Connection
Resources

OTHER TOOLS

Fitting Trap Adapter with Washer & Nut SpgxSlip

Installed in an ABS DWV piping system to provide a smooth transition from a Hub to a male national pipe thread (MPT).

Features
• Spigot connection can be single step ABS solvent cemented to an ABS DWV Hub
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Teflon tape is recommended for threaded joints
• Hand tighten cleanout plug plus a half turn provides a complete seal
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102800
1-1/4" ABS DWV Trap Adapter (Fitting Male Adapter) Spigot X Male National Pipe Thread (MPT)
102800A
1-1/4" ABS DWV Trap Adapter with Polyethylene Washer and Nut Spigot X Slip Connection
102801A
1-1/2" ABS DWV Trap Adapter with Polyethylene Washer and Nut Spigot X Slip Connection
102801A2
1-1/2" X 1-1/4" ABS DWV Trap Adapter with Polyethylene Washer and Nut Spigot X Slip Connection
102802A
2" ABS DWV Trap Adapter with Washer and Nut Spigot X Slip Connection
103211Y
1-1/2" X 1-1/4" ABS DWV Trap Adapter with Polyethylene Washer and Nut, Spigot X Slip Connection
Resources

OTHER TOOLS

Slip Joint Nut

Used as a replacement or repair part for items such as ABS DWV combination, copper pipe and sanitary tee trap adapters.

Features
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
103930
1-1/4" ABS DWV Slip Joint Nut
103931
1-1/2" ABS DWV Slip Joint Nut
103932
2" ABS DWV Slip Joint Nut
103933
1-1/4'' X 1-1/2'' ABS DWV Slip Joint Nut
Resources

OTHER TOOLS

Sanitary Tee Trap Adapter HxHxSlip Joint

Normally Installed under a 1-1/2" Sink Drain to provide a slip connection from the Drain Tail Pipe to a 1-1/2" P-Trap. Also allows for a smooth transition from a 1-1/2" horizontal pipe line to a 1-1/2" vertical line.

Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
112171A
1-1/2" PVC DWV Sanitary Tee Trap Adapter with Washer and Nut H X H X Slip Joint
Resources

OTHER TOOLS

Sanitary Tee Sink Strainer Adapter

Normally Installed under a 1-1/2" Sink Drain Strainer to provide a Gasketed Threaded connection from the strainer basket Tail Pipe to a 1-1/2" P-Trap. Also allows for a smooth transition from a 1-1/2" horizontal pipe line to a 1-1/2" vertical line.

Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
112191A
1-1/2" PVC DWV Sanitary Tee Sink Strainer Adapter H X H X Sink Strainer Adapter Nut and Washer
Resources

OTHER TOOLS

90° Sink Strainer Adapter

Installed in an ABS DWV piping system from a 1-1/2" Sink Strainer tail pipe using a threaded 90 Degree Trap Adapter, into a 1-1/2" ABS DWV Pipe.

Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Type 1 allows for up to 3" (7.6cm) of travel
• Flow direction and proper degree of extension indicated on the Expansion Joint
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
112291A
1-1/2" PVC DWV 90 Degree Sink Strainer Adapter H X Sink Strainer Adapter Nut and Gasket
Resources

OTHER TOOLS

Trap Adapter with One Piece Poly Nut HxSlip

Installed under a bathroom or kitchen sink to transition from the tubular sink drain tale piece to the ABS DWV P-Trap assembly.

Features
• One piece nut and gasket assembly makes installation easier
• Hub connection can be single step ABS solvent cemented to a 1-1/2" Pipe or Spigot connection
• Injection molded body in durable ABS plastic and using a reliable One-Piece Polyethylene nut and gasket
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Friction fitted to DWV Pipe sizes
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
102853A
1-1/2'' ABS DWV Trap Adapter with One-Piece Polyethylene Nut H X Slip Connection
102855A
1-1/4" X 1-1/2" ABS DWV Trap Adapter with One-Piece Polyethylene Nut H X Slip Connection
Resources

OTHER TOOLS

We are always here to help.

Do not hesitate to get in touch for any reason.

CONTACT US

Feedback

How could we improve?

Tell us what you want to see.

© 2023 Canplas. All Rights Reserved. WM