English- Français (French)
Appliance/Dishwasher Wye
Installed in an ABS DWV piping system in the drain line beneath the sink before the P-Trap to allow waste water from an appliance (dishwasher) to flow into the Drain Pipe or allow waste water to be directed to a Floor Drain to ensure that the Drain P-Trap does not run dry, allowing Sewer gas to enter the home.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Snap in plug is molded on fitting for use during rough in
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Snap in plug is molded on fitting for use during rough in
• Teflon tape is recommended for threaded joints
• Approved for both Vertical and Horizontal Installations
Submittal Sheets
Resources
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" X 1-1/2" X 1/2" ABS DWV appliance wye / Graywater Trap Primer H X H X Spigot
1-1/2" X 1-1/2" X 3/4" ABS DWV appliance wye / Graywater Trap Primer H X H X Spigot
1-1/2" X 1-1/2" X 1" ABS DWV appliance wye / Graywater Trap Primer H X H X Spigot
Resources
OTHER TOOLS
Wye HxHxH
Installed in an ABS DWV piping system to provide a smooth transition from a horizontal branch line to a vertical drainage line. Often used with a threaded fitting cleanout adapter and plug, to allow access to the piping system.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Hand tighten plus a half turn provides a complete seal
• Injection molded in durable ABS plastic
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Normally used in the drainage portion of the DWV system only
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/4" ABS DWV Wye H X H X H
1-1/2" ABS DWV Wye H X H X H
1-1/2" ABS DWV Wye H X H X H
2" ABS DWV Wye H X H X H
2" ABS DWV Wye H X H X H
3" ABS DWV Wye H X H X H
4" ABS DWV Wye H X H X H
4" ABS DWV Wye H X H X H
6" ABS DWV Wye H X H X H
1-1/2" X 1-1/2" X 1-1/4" ABS DWV Wye H X H X H
2" X 1-1/2" X 1-1/2" ABS DWV Wye H X H X H
2'' X 2" X 1-1/2" ABS DWV Wye H X H X H
2'' X 2" X 1-1/2" ABS DWV Wye H X H X H
3" X 3" X 2" ABS DWV Wye H X H X H
3" X 3" X 2" ABS DWV Wye H X H X H
4" X 4" X 3" ABS DWV Wye H X H X H
4" X 4" X 3" ABS DWV Wye H X H X H
4" X 4" X 2" ABS DWV Wye H X H X H
4" X 4" X 2" ABS DWV Wye H X H X H
4 X 4 X 1-1/2" ABS DWV Wye
3" X 3" X 1-1/2" ABS DWV Wye H X H X H
3" X 3" X 1-1/2" ABS DWV Wye H X H X H
6" X 6" X 3" ABS DWV Wye H X H X H
6" X 6" X 4" ABS DWV Wye H X H X H
Resources
OTHER TOOLS
Appliance Adapter
Installed in a 1-1/2" ABS DWV piping system to allow waste water from an appliance (dishwasher) or to collect condensate to flow into the Drain Pipe. Used with a Canplas part 102151 Sanitary Tee Installed in a horizontal or vertical portion of the 1-1/2" drainage pipe. the 1/2" spigot is connected to dishwasher or condensate tubing.Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Approved for both Vertical and Horizontal Installations
Submittal Sheets
Resources
• Approved for both Vertical and Horizontal Installations
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" X 1/2'' ABS DWV Appliance Adapter Spigot X Spigot
Resources
OTHER TOOLS
Double Wye HxHxHxH
Installed in a vertical ABS DWV piping system to allow for a smooth transition from two horizontal branch lines into the vertical drainage line.Features
• Hub connections can be single step ABS solvent cemented to pipe or spigot connections
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Injection molded in durable ABS plastic
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" ABS DWV Double Wye H X H X H X H
2" ABS DWV Double Wye H X H X H X H
3" ABS DWV Double Wye H X H X H X H
4" ABS DWV Double Wye H X H X H X H
2" X 2" X 1-1/2" X 1-1/2" ABS DWV Double Wye H X H X H X H
3" X 3" X 1-1/2" X 1-1/2" ABS DWV Double Wye H X H X H X H
3" X 3" X 2" X 2" ABS DWV Double Wye H X H X H X H
4" X 4" X 2" X 2" ABS DWV Double Wye H X H X H X H
4" X 4" X 3" X 3" ABS DWV Double Wye H X H X H X H
Resources
OTHER TOOLS
Long Turn Tee Wye Single HxHxH
Installed in an ABS DWV piping system in some plumbing code areas to connect a horizontal branch line to a vertical drain pipe instead of a conventional tee fitting. Provides a smoother transition.Features
• Hub connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Injection molded in durable ABS plastic
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Injection molded in durable ABS plastic
• Normally used in the drainage portion of the DWV system only
Submittal Sheets
Resources
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" X 1-1/2" X 1-1/2" ABS DWV Single Long Turn Tee Wye
2" X 2" X 2" ABS DWV Single Long Turn Tee Wye
3" X 3" X 3" ABS DWV Single Long Turn Tee Wye
4" X 4" X 4" ABS DWV Single Long Turn Tee Wye
2''X 1-1/2" X 1-1/2" ABS DWV Single Long Turn Tee Wye
2''X 1-1/2" X 2" ABS DWV Single Long Turn Tee Wye
2''X 2" X 1-1/2" ABS DWV Single Long Turn Tee Wye
3''X 3" X 1-1/2" ABS DWV Single Long Turn Tee Wye
3''X 3" X 2" ABS DWV Single Long Turn Tee Wye
4''X 4" X 2" ABS DWV Single Long Turn Tee Wye
4''X 4" X 3" ABS DWV Single Long Turn Tee Wye
Resources
OTHER TOOLS
Wye, Street SpgxHxH
Installed in a ABS DWV piping system Hub to provide a smooth transition from a horizontal branch line to a vertical drainage line. Often used with a threaded fitting cleanout adapter and plug, to allow access to the piping system.Features
• Hub and spigot connections can be single step ABS solvent cemented
• Injection molded in durable ABS plastic
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Injection molded in durable ABS plastic
• For use in both the drainage and venting sections of the plumbing installation
• Service temperature rated at -40 Degrees C (-40 F) to +80C (180F)
• Hand tighten plus a half turn provides a complete seal
• Teflon tape is recommended for threaded joints
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Submittal Sheets
Resources
• Longer 4" Extended spigot reduces the number of fittings needed for thick flooring
Click on the Part # below to generate the submittal sheet.
Part #
DESCRIPTION
1-1/2" ABS DWV Street Wye Spigot X H X H
2" ABS DWV Street Wye Spigot X H X H
3" ABS DWV Street Wye Spigot X H X H
3" ABS DWV Street Wye Spigot X H X H
4" ABS DWV Street Wye Spigot X H X H
3" X 3" X 2" ABS DWV Reducing Street Wye Spigot X H X H
3" X 3" X 1-1/2" ABS DWV Reducing Street Wye Spigot X H X H
Resources
OTHER TOOLS
We are always here to help.
Do not hesitate to get in touch for any reason.
